|Specifications||Audible Range |
|Wall Mounting |
|Specifications||Audible Range |
|Wall Mounting |
Ø Complies to IS2189:1999 and tested by ERTL ( N )
Ø Built with 2x16 character LCD display with backlight
Ø Zone Isolation facility with Zone voltage cut off
Ø LCD display and LED indication for FIRE, SHORT, OPEN & ISOLATE of each zone
Ø Front panel LED indication for MAINS ON, CHARGING,LOW BATTERY &
Ø Extra potential free contact for FIRE and FAULT
Ø Individual hooter of each Zone
Ø 02-wire communication via RS-485 for repeater and slave
Ø Compatible to all types of conventional detectors
Ø Lamp test facility along with manual test of FIRE , SHORT & OPENSYSTEM ON from front facia
The Oriel Series of Microprocessor based Fire Alarm Panels are an upgraded version which provides a reliable and cost effective solutions to fire detection, from small to large size installations which have 4, 6, 8 & could go up to 60 zones of selecting models and features. These units have been designed to offer high standards of performance, reliability and quality and comply with IS 2189 : 1999 and tested by the ERTL (N) & System Sensor.
• Low profile design
• Low current draw
• Backward compatible with Series 100 detector range of bases
• Wide operating voltage 8 to 30VDC
• Bi-colour LED detector status indicator
• Automatic drift compensation
• Programmable sensitivity
• Addressable feature
• Advanced maintenance features via remote hand-held test unit
• Range of detector bases available
• Tested and approved to EN54 – 7:2000 (Amendment 1)
Manual Call Point AD- 110 (ABS)
The Manual Call Point is tough, durable & highly visible. Alarm LED is provided inside the Call Point to indicate the Alarm condition.
Remote Indicating Lamp AD-301(MS)
The unit is designed to ensure that Alarm Signal can be actually transmitted to all locations. To prevent any missing signal specially for the close room.
Siren cum Strobe AD -ESF1
The Sounder cum strobe is designed to
give the audio & visual indication in case
Auto Dialer AD- 01
GSM Dialer GD- 02
· Totally Micro controller Based System
· 2 – Line, 16 – Character LCD With Back light
· 128 – Event Memory Stored In Nonvolatile Memory.
Photo Electric Smoke Detector
The series 100 range of Conventional detectors has been produced using the latest in manufacturing and design techniques, pushing out the boundaries of existing conventional detector technology.The Series 100 detector incorporates a bi-colour LED indicator. The integral LED is blinking Green when the detector’s status is Normal and turns steady Red when it is in Alarm.
This benefits the user by providing clear, instant visual indication of the detector’s condition. An optional remote LED annunciator may be used to repeat any alarm signal. A laser-based hand held Remote Test Unit can be used in conjunction with the detectors for alarm test purpose. The unit transmits a coded message, preventing spurious alarms being generated by other laser-based devices.
A variety of detector bases can be used with the AD 338 – 2L detector, providing application flexibility and compatibility with a wide range of Fire Alarm Control Panels. All bases are fitted with a shorting spring to permit circuit testing prior to fitting the detectors and have a tamper resistance feature, which when activated prevents removal of the detector without the use of a tool.
All Detectors are covered by our extended 3 year warranty.
The AD 338 – 2HL photoelectric smoke / thermal detector incorporates an optical chamber and a thermal element, which in turn are continually monitored by an on board processor by using algorithms developed specifically for the unit. An alarm signal is only enabled in the detector once the processor is satisfied that an incipient fire has been detected. By using a combination of inputs, the incidence of nuisance alarms is reduced while at the same time, the response time to an actual fire is also improved.
‘Drift Compensation’ algorithms are one of the key features of the AD 338 – 2HL detector. These algorithms ensure a consistent alarm sensitivity threshold for periods between service intervals. This provides the user with both a reduction in the frequency of nuisance alarms and maintenance savings by extending the period before cleaning of the detector chamber is required.
Rate of Rise Thermal Detector
The AD 318 – 2L thermal detector incorporates an Application Specific Integrated Circuit (ASIC). Combined with the latest in thermal element technology the detector provides efficient and accurate detection of fire, especially in environments such as bars or kitchens where smoke detectors are inappropriate due to high level of airborne contamination.
Optical Smoke Detector UL certified
All of AD333 series detectors meet the requirements of UL 268 and EN 54-715 for use in Fire Alarm signaling systems. They are intended for use in 2 wire l4 wire Class A or B supervised zone circuits. The AD 333 Series detectors are subject to panel compatibility limits and compliance with corresponding NFPA 72E standards, local codes, and ordinances.
AD-333 series include 2 wire and 4 wire detectors, which provide fast and reliable response to photoelectric smoke and heat (135°F) detection. While the smoke and heat detection circuits operate independently, their outputs being “OR” connected. The detector provide the fire detection performance by acting as a smoke sensor and lor a 135°F heat detector ct the same location.
GD-625 series detectors is effective for detecting any buildup of natural gas and liquid gas, ideal for use in commercial properties can be connected with fire alarm control panel with 2 wire, as a control unit for operation as part of gas detection. The gas alarm should be mounted high (for methane gas) or low (for LPG gas) location.
Horizontal Double Mounting Siren